This adapter allows you to connect a Reprapdiscound GLCD panel to a Smoothieboard easily.

glcdav2.jpg

All of the panel's functionalities are available : 

  • Display
  • Encoder selector
  • Button
  • Buzzer
  • SD card

Open Harware

The Source is on GitHub

Getting one

You can now get a RRDGLCD Adapter here.
for US another version comming soon here

Two versions

Both versions look a bit different, but are functionally identical and are used the same way. The RobotSeed version is pictured here, but the instructions are identical for the Uberclock version.

Assembly

glcdav2_kit.jpg
place the 3-pin connectors below the pcb
glcdav2_weld0.jpg
and solder
glcdav2_weld1.jpg
Mount the exp1 & exp2 connectors, and solder
glcdav2_orig.jpgrrdglcdvo.png
on some rrdglcd the connector are reversed
glcdav2_copy.jpgrrdglcdcopy.png

Power supply

If smoothieboard has good 5v regulator, or a 5V power supply, the panel of the power supply can be drawn from this one by means of a diode (ex 1N5817).
glcdav2_power1.jpg
if not, please install a voltage regulator Recom 785.0-1
glcdav2_power2.jpg
the diode and regulator may be mounted at the same time

Configuration

the adapter is configured for smoothieboard v1.0a and newest

for v1.0 smoothieboard, configure the PCB
glcdav2_config1.jpgglcdav2_config2.jpg
cut the jumper track, and drop a welding goute on the other part of the jumper

Use

solder the connector missing
glcdv2_smoothie.png

Update firmware (version after october 2014), see Flashing Smoothie firmware
edit the config file on the µSD

# config settings
panel.enable                          true              # set to true to enable the panel code
panel.lcd                             reprap_discount_glcd     # set type of panel
panel.spi_channel                     0                 # spi channel to use  ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
panel.spi_cs_pin                      0.16              # spi chip select     ; GLCD EXP1 Pin 4
panel.encoder_a_pin                   3.25!^            # encoder pin         ; GLCD EXP2 Pin 3
panel.encoder_b_pin                   3.26!^            # encoder pin         ; GLCD EXP2 Pin 5
panel.click_button_pin                1.30!^            # click button        ; GLCD EXP1 Pin 2
panel.buzz_pin                        1.31              # pin for buzzer      ; GLCD EXP1 Pin 1
panel.back_button_pin                 2.11!^            # 2.11 menu back      ; GLCD EXP2 Pin 8
# setup for external sd card on the GLCD which uses the onboard sdcard SPI port
panel.external_sd                     true              # set to true if there is an extrernal sdcard on the panel
panel.external_sd.spi_channel         1                 # set spi channel the sdcard is on
panel.external_sd.spi_cs_pin          0.28              # set spi chip select for the sdcard (or any spare pin)
panel.external_sd.sdcd_pin            0.27!^            # sd detect signal (set to nc if no sdcard detect) (or any spare pin)

If you do not want to use the buzzer, leaving out the panel.buzz_pin line will leave the pin floating. As there is no pull-down on the buzzer, it will keep buzzing. To avoid this, you can either solder a pull-down resistor on the adapter board or you can use this little hack:
switch.nonoise.enable                        true
switch.nonoise.output_pin                    1.31v
switch.nonoise.output_type                   digital

This will create a pseudo-switch that does nothing, but it will enable the pull-down on the pin. You have to leave out the panel.buzz_pin line.

connect exp1 & exp2, and plug on the smotthieboard

Adapter v1

adapter.jpg

The V1 of this adapter was not capable of accessing the panel's SD card slot.

This functionality can be made available on the v1 by cutting track on pcb

gcldv1_03.jpg

And soldering a cable under the pcb

gcldv1_04.jpg

This site is a WIki, which means you are very welcome to help us improve it. Help on how to do that can be found at the Editing the Wiki page . You can edit any page by clicking the "Edit" button bellow :