Forum » Smoothie Firmware / General
Number of threads: 1186
Number of posts: 5355
rss icon RSS: New threads | New posts
Order by:
Last post date
Thread starting date
Create a new thread
Thread name Started Posts Recent post
I switched to external stepper drivers because the internal ones had too little power at higher speed--> lost steps. However with the external ones it seems that there is also some sort of drifting.
by: Panda1337Panda1337
25 Jun 2018 08:39
2 by arthurwolfarthurwolf
30 Jun 2018 10:32 Jump!
I think I connected everything right, but the motors do not move.
by: brainy19brainy19
23 Jun 2018 02:34
5 by arthurwolfarthurwolf
30 Jun 2018 10:25 Jump!
I need help wiring my clearpath servos to my smoothieboard
by: MHoppMHopp
08 Jun 2018 00:28
7 by Teknic_ServoTeknic_Servo
29 Jun 2018 18:03 Jump!
I need advice on connecting my 15W Laser diode to my smoothieboard, the laser has 3 wires, GND, +12 and PWM. Every time
by: QJonasQJonas
22 Jun 2018 08:44
6 by QJonasQJonas
28 Jun 2018 06:48 Jump!
Why doesn't z probe pay attention to the z-min endstop?
by: Rachel RandRachel Rand
24 Jun 2018 16:58
3 by Rachel RandRachel Rand
24 Jun 2018 19:20 Jump!
we have problems with our current laser controlling card. wondering about smoothie.
by: aljalj
15 May 2018 15:04
2 by arthurwolfarthurwolf
16 Jun 2018 10:43 Jump!
how to displaying A B or C axis position on lcd (mode cnc=true)
by: sularsular
09 May 2018 06:22
3 by arthurwolfarthurwolf
16 Jun 2018 10:38 Jump!
Muh endstops are always on...
by: swattiswatti
15 May 2018 17:56
6 by arthurwolfarthurwolf
16 Jun 2018 10:37 Jump!
by: MHoppMHopp
14 Jun 2018 04:47
6 by arthurwolfarthurwolf
16 Jun 2018 10:21 Jump!
by: singhm29singhm29
17 May 2018 06:39
9 by Adam TrefonidesAdam Trefonides
14 Jun 2018 22:04 Jump!
by: singhm29singhm29
13 Jun 2018 22:21
2 by arthurwolfarthurwolf
14 Jun 2018 10:24 Jump!
When print is finished, i get nan as the co-ordinate of Z axis.
by: Lukas LozoLukas Lozo
30 Mar 2018 00:52
3 by Lukas LozoLukas Lozo
13 Jun 2018 10:33 Jump!
by: playludescplayludesc
11 Jun 2018 01:51
4 by arthurwolfarthurwolf
12 Jun 2018 13:17 Jump!
How can I get two stepper motors to follow the same g-code, but home to their own endstop? To say, automatically sync up a dual Z-axis, or in my case, square up the X and Y for an MPCNC.
by: playludescplayludesc
25 Apr 2018 04:02
7 by playludescplayludesc
11 Jun 2018 08:51 Jump!
smoothieware hangs during print with communication active on USB or Ethernet port.
by: Lukas LozoLukas Lozo
25 Mar 2018 10:24
6 by arthurwolfarthurwolf
10 Jun 2018 15:50 Jump!
I make updates to the Config.txt causes Azteeg X5 mini v3 not to boot.
by: jjlinkjjlink
07 Jun 2018 23:11
11 by jjlinkjjlink
08 Jun 2018 17:29 Jump!
by: Lukas LozoLukas Lozo
22 Nov 2017 14:08
2 by arthurwolfarthurwolf
08 Jun 2018 16:20 Jump!
by: peterpandampeterpandam
23 May 2018 09:04
3 by arthurwolfarthurwolf
08 Jun 2018 16:14 Jump!
Continuation to my previous topic with a new issue
by: swattiswatti
23 May 2018 11:56
2 by Lukas LozoLukas Lozo
08 Jun 2018 15:58 Jump!
No servo signal on 3.25
by: Rachel RandRachel Rand
31 May 2018 16:08
27 by Rachel RandRachel Rand
06 Jun 2018 13:52 Jump!

This site is a WIki, which means you are very welcome to help us improve it. Help on how to do that can be found at the Editing the Wiki page . You can edit any page by clicking the "Edit" button bellow :