# Your guide to installing Smoothieboard in a CNC Milling Machine

Although not as common as the Smoothiefied 3D printer, the CNC mill machine is fairly simple to Smoothiefy.

This is a step-by-step guide to connecting your board to the various components of the CNC mill machine, configuring everything, from the beginning to actually milling material.

This guide is a community effort, and this page is a Wiki. Please don't hesitate to edit it to fix mistakes and add information, any help is very welcome.

On a typical CNC mill or CNC router setup, installing a Smoothieboard will mean you do the following things :

• Read all of the guide before you start, best way to avoid mistakes
• Install some Software to talk to your board
• Install the Windows drivers if using that OS
• Connect your board via USB and practice talking to it
• Take a look at the configuration
• Wire your power supply and provide it with power
• Wire the power supply to Smoothieboard's motor input
• Connect motors to the stepper motor driver outputs
• Connect Endstops to the endstop inputs
• Test your endstops by homing the machine
• Connect any spindle controller you may have
• Connect, configure and test any probes you may have
• Setup leveling if relevant
• Configure your CAM software and generate a G-code file
• Use your host software to send your new G-code file to the Smoothieboard
• Watch as the machine cuts using your new Smoothieboard system
• Be happy

This guide will walk through everything you need to accomplish to successfully perform these steps.

At the end of this guide, you should have a fully working machine.

USB Connectors

Smoothie uses USB-B

## Unboxing

Your Smoothieboard comes with a microSD card in the microSD slot.

The boards come pre-flashed. With a basic configuration file installed on the SD card, no preparation is needed before you can connect Smoothieboard to your computer and start interacting with it.

The first thing you might want to do before you start connecting your board, is to look at our list of Software, and install a "host" program to talk to the board.

## Connecting via USB

A good first step is to connect your board to your computer to familiarize yourself with it. Connect a USB-B cable to the USB connector on the board, and to your computer.

SD card

Files on your Smoothieboard's SD card

A moment after connection, your computer will recognize the Smoothieboard as a USB Mass Storage Device (like a USB disk-drive or a SD card reader), showing you the files present on the SD card. Drivers are needed for Windows 7/8, while Linux and Mac OS X directly support the device, you can find those drivers here.

This allows you to add, copy, edit or delete any file you'd like. Already present on the SD card is a file named "config". This file contains all of the configuration options for your board and is read when you start or reset your board. You edit the configuration simply by editing this file in a Text Editor, saving it and resetting the board. No need to recompile or flash the board.

#### More on configuration

The SD card can also be used to flash a more recent version of the firmware to your board, see where to get the binary file and how to flash it via the SD card.
It can also be used to store and play G-Code files, see Player.

USB Mass Storage is not the only thing you get when you connect the board. The board also exposes a USB CDC Serial interface, allowing you to send G-Code and receive answers. (There is also a DFU interface for flashing firmwares but that's mostly for developers).

The CDC (Serial) interface is the interface host programs like Pronterface use to allow you to interact with your machine. If you are already familiar with it, you can try connecting right now and get an answer from the board. If not, we explain it all later in this guide.

## Connecting via the network

Network

Hope you have less cables than this

The other main communication interface present on the Smoothieboard, apart from the USB port, is the Ethernet port, which allows you to connect your board to your local Ethernet network, and talk to the board via TCP/IP.

This is the same kind of technology you would find on a network-connected 2D printer for example.

It allows you to access a web interface the board serves, and control the machine via your browser.

It also allows you to connect some software that supports it ( like Pronterface and Visicut ) to your Smoothieboard via the network.

Network is disabled by default, but is very easy to enable and configure.

It is also the recommended main method of communicating with your Smoothieboard.

You can find all the information you need about using the network interface here : Network interface

You do this by downloading the latest firmware.bin file, pasting it unto the SD card, and resetting the card.

Then, the new firmware will "flash" ( you will see the LEDs on the board do a little "dance" ), and you now have the latest version.

This is particularly useful if you ever need to ask for help, as people helping you will be assuming you have the latest version.

You can find the file, and information on how to flash it, at Flashing Smoothie Firmware.

## Warnings

Before you start wiring your machine's elements to the board, there are several things you need to keep in mind and be careful about during all of the assembly.

Make sure you read this. Seriously.

Power connections

Note the inversion between the 5mm and 3.5mm connectors

#### Polarity

Always make sure the polarity is correct when wiring in power inputs (coming from the Power Supply). Reversed polarity can damage or destroy all or part of your board. Polarity is indicated on the board itself by the + and - signs. Double check. On older versions of the board, markings are partially hidden by the connector, making it confusing. Rely on only the diagrams.

To check the polarity of your power source, attach your multimeter probes to the two wires of your power source respectively. If the voltmeter reading is positive it implies that the red probe is connected to the positive wire (+) and the black probe to the negative wire (-).

The main (labeled VBB) power input has a reverse polarity protection, however, it will not hold forever. As soon as you notice something is wrong, turn the power supply off and check again.

#### Disconnecting

Never disconnect or connect stepper motors from the stepper motor drivers while the board is powered (i.e., when the Power Supply is turned on).

The drivers have very good protection against most possible problems and are very hard to destroy accidentally. But it is possible.

#### Shorts

Be careful that nothing metallic ever touches the board while it is powered on. Falling screwdrivers, nuts and bolts can cause shorts and destroy the board.
Check the board before powering it on.
Do not press the reset button with anything metallic, as you could slip and cause a short, use a plastic screwdriver or the like.

#### Use the right connector

Always check the schematic before connecting power sources (coming from the Power Supply) to the board. Connected to the wrong connector can destroy components. A common example of this problem is plugging a power input cable, into the connector for an output, or plugging the limit switches in backwards.

#### Crimping

Make absolutely sure of your connections using crimps or screw terminals, from wires to any type of connector, are very careful and well done. Connections (to the stepper motors for example) lost while the machine is running can destroy your board.

#### Markings

In the case of the VBB power input, be careful. If your board came with connectors pre-soldered, the 5mm connector is present, and the polarity of that connector is that of the large traces in the wiring diagram to the right (red is +, blue is -). On some boards, the marking on the boards may be hidden by the connector itself, so for VBB, do not rely on the markings on the board, but on the diagrams on this page. However, if you did not get your connectors soldered, and want to solder a 3.5mm connector instead of a 5mm connector, also note that the polarity is the opposite.

#### USB v Ethernet

USB can, in some setups, be subject to interference, which causes disconnections, and can ruin your work. This is very hard to prevent if it happens even in normal conditions. Ethernet, on the other hand, does not have this problem: save yourself the trouble, and use Ethernet right away. It's very nice. See Network for information on how to set it up.

If you receive a bad board, you will get a replacement. But if you destroy your own board, your only options will be to fix it yourself (which can be quite difficult), or get a new one.

This is why it is very important you make sure you do not destroy your own board. Smoothieboard is reasonably protected, but there are still things that will destroy it. The general idea is: if a part of the board gets too much power, it will get destroyed. Here are some common mistake users do that cause the board to get too much power and die:

• Plugging 12-24v (motor power) into anything you are not supposed to. Like the 5V line, or an end-stop or thermistor input for example. Problems with the 5V or 3.3V power are not as much of a problem as the board is 5V-tolerant, so wrong connections and shorts should be okay as long as they do not last too long.
• Shorting 12-24v to anything else, which is essentially the same as plugging it into a place you are not supposed to (see above). This can happen by dropping a metal object onto the board, bad soldering, loose wires, un-protected wires, etc …
• Using an inductive load (like a motor, fan or solenoid) on a MOSFET, without a diode across (see Fan documentation).

The general idea here is: always make sure everything is clean, and double-check everything before turning the power on. You can not learn by making mistakes here, as mistakes will likely cost you your board.

Electrostatic discharge can also destroy your board : make sure you properly ground everything.

#### Heater safety

If your machine contains any heating element and uses the temperature control module to control it, please make sure you read the section about implementing all safety measures here, and implement as many as you can. Fires will kill you if you don't.

#### Grounding

Make sure your machine's case and electronics are properly grounded, also make sure your location's electrical installation's grounding is correctly done. See for example :

#### Environmental hazards

Be aware of your environment : it's not just the machine itself.

• On a laser cutter, the machine vents large quantities of toxic smoke and gas, make sure it is very well evacuated to a place where no-one is breathing them
• On a CNC-mill, dusts, like wood dust for example, can be explosive if they come in contact with a flame, be careful and take measures to limit dust in the air
• On a 3D printer, the acetone used to clean things is very flammable, and the sprays used to increase bed adherence are explosive, store them adequately and be careful when using them

In particular, you are even more in danger if you are using your machine in a confined space, always be on the watch for safety issues.

For a good read about safety, you can refer to the RepRap Wiki documentation on the subject

## CNC firmware

Smoothie firmware tries to create a single firmware for all types of machines ( you then adapt the firmware to your machine type by changing the configuration ).

However, due to lack of flash space on the v1 hardware, the v1 Smoothie firmware has an optional special "CNC" build.

It includes :

• A special CNC version of the Panel screens
• grbl_mode enabled by default ( which means Smoothie interprets G-code as CNC G-code rather than 3D-printing G-code )
• The Spindle module

You will find informations on flashing the firmware at getting-smoothie

## Logic power

Logic power inputs

There are different ways of providing logic power to your board

Your board needs two sorts of power to work : 12-24V power to turn motors, heat hotends, etc, and 5V ( or "logic" ) power to power the microcontroller ( the brain ).

There are three ways to provide 5V power to the board :

• By plugging a USB cable in, USB cables provide 5V
• By soldering a voltageregulator to the board ( and providing 12+24V, which the voltage regulator then turns into 5V )
• By providing 5V directly to the 5V power input ( next to the VBB power input )

If you want to keep it simple, the easiest solution is just to connect your Smoothieboard to your computer via USB.

A power supply

Be careful, mains voltage is dangerous

## Main Power Input

Without power, your board can not do much. The board uses power to move stepper motors, and power heating elements, fans, and others.

How to choose a power supply unit (PSU) :
Voltage (V)
Can be from 12 to 24V. While most of the components on the Smoothieboard are rated up to 32V, it is not recommended or supported to use that voltage. 12V PSUs are more common, and generally cheaper. However, the higher the voltage, the more you will get out of your stepper motors. This is the reason some designers use 24V PSUs. However, be careful that with a 24V PSU, you will need 24V fans, and will need to reduce the PWM setting for your heating elements.

### Setup

Make sure you use a Regulated Power Supply, make sure you connect the ground wire for the mains to the power supply, and if it has a fan, make sure it has sufficient space around it to let air flow and cool it appropriately.

To wire the power supply unit to mains (wall AC power), make sure you connect the right colored wires to the right connectors on the PSU. The 3 connectors are "live", "neutral" and "ground". Color changes from cable to cable, you can find charts for your specific country/cable on the internet, but the following colors are the most common:

• US: Black = Load/Live, White = Neutral, Green = Earth
• Europe: Brown = Load/Live, light Blue = Neutral, Yellow/Green = Earth

Once the wires connected to the PSU, make sure none of your computers is doing something important (like a system upgrade). In case something goes wrong, plug the PSU into a power strip with an on/off button. Then turn that button ON. If your house loses power, you did something wrong. If an LED illuminates on the PSU, everything is fine: unplug the PSU and continue.

If you are new to wiring, please check our how to wire guide.

#### Don't die

NEVER manipulate mains (220/110V) power wires while they are plugged into the wall plug. Unpleasantness and/or death are common consequences of not respecting this rule.

Ground your printer's frame by connecting it to the Earth terminal on your power supply. In the (unlikely) event that a power supply wire comes undone and touches the printer's frame, this will prevent you from getting an unpleasant and/or deadly shock.

Now that the PSU is getting mains power, your PSU is converting it into 12 or 24V power. You need to connect wires from it to the Smoothieboard to provide power.

The most important thing is to respect polarity : + goes to +, - goes to -. On the PSU, + terminals are indicated as +, V+, 12V+ or 24V+. Ground (-) terminals are indicated as -, V-, COM or GND.

On the Smoothieboard they are indicated simply as + and -.

By convention, black (sometimes brown) wires are used for ground, and red (sometimes orange, white or yellow) wires are used for power connections.

Once the wires are correctly connected, you can turn the PSU ON. If everything was done correctly, the red LED (marked VBB) on the Smoothieboard will light up brightly.

#### Be careful

If it does not, immediately turn the PSU off.

Check polarity, and check all the connections are strong and properly done.

When you turn the PSU on, make sure you are ready to immediately turn it back off.

Now that the board has power, you can use that power to move things!

### Emergency stop

It is recommended you setup an emergency stop button on your machine, so that in case of a problem, you can easily and quickly turn the machine off. For information on how to do this, please read EmergencyStop.

## Stepper Motors

A bit of theory :

« A stepper motor (or step motor) is a brushless DC electric motor that divides a full rotation of the motor into a number of equal steps. The motor's position can then be commanded to move and hold at one of these steps without any feedback sensor (an open-loop controller). » (Wikipedia)

Because they work by steps, and you can accurately control how many steps you move in each direction, stepper motors are a very practical way of moving things to a desired position. This makes them great for most CNC applications.

Smoothie comes with stepper motor drivers designed for bipolar stepper motors, with a maximum current rating of 2 Amps.

#### Choosing stepper motors

There is a very wide variety of stepper motors around. Bigger motors are generally more powerful. For a given size, motors will have different torques, max speeds, and different capacities to maintain torque as speed increases.

It is important you choose the right motor for your application. The most common mistake is to choose a high inductance motor. There are two main "families" of motors out there : high inductance motors are mostly designed for maintaining position and moving rarely ( like on a telescope mount ), and low inductance motors are designed for moving often, and at high speeds ( like on a CNC mill or 3D printer ).

If you use a high inductance stepper motor with a Smoothieboard ( or any "CNC" stepper motor driver ), not only will you get bad speed/torque performance, but when moving the stepper motor ( or axis ) by hand, very high voltage will be generated, which can destroy your stepper motor driver.

You can recognize a "high inductance" stepper motor by the fact that it's rated inductance is high, in general higher than 10mH is bad. If your motor doesn't tell you it's inductance, rated voltage is also an indication : high inductance stepper motors usually have high rated voltages, a typical value being 12V, where "CNC" steppers have voltage bellow 5V.
This is not what you want, you want a low inductance stepper motor, with an inductance ideally bellow 10mH, and a rated voltage ideally bellow 5V

The reprap community defines a good stepper motor like this :

Ideal stepper is (for reprap printers and similar small CNC using microstepping drivers on 12-24v supply) NEMA17 size, rated 1.5A to 1.8A or less, 1-4Ω winding resistance, 3 to 8 mH, 62oz.in (0.44Nm, 4.5kg.cm) or more of torque, 1.8 or 0.9 degrees per step (200/400 steps/rev respectively), for example the kysan 1124090/42BYGH4803 or the rattm 17HS8401 or Wantai


Stepper motor wiring

Be careful you get the coils right

### Wiring

#### Direct wiring

Bipolar stepper motors have two poles (bi-polar). Each pole is connected to two wires. That's 4 wires coming out of your stepper motor. These have to be connected to your Smoothieboard.

Each stepper motor driver on the Smoothieboard has 4 connections to that effect. (Stepper motor drivers are labeled M1, M2 etc …)

The tricky thing is often to find out which wires connect to which poles. If you just wire things at random, you have a chance it will work, but let's be scientific about it. Several methods:

Now to connect the wires to the Smoothieboard. Let's call one coil A, and the other coil B. It doesn't matter which is which. Polarity also doesn't matter, all it changes is the direction the motor turns, and you can change that in the configuration file. Now simply connect your two wires to the Smoothieboard's 4 pins for that stepper motor driver as such : AABB or BBAA. Other combinations like ABBA or ABAB will not work.

How to properly connect stepper motors

If you don't get it right, it won't work properly

Wiring a stepper motor to a stepper motor driver.

In this example, a stepper motor is connected to the M1 driver, and power is provided to VBB ( the main power input ).

#### External Stepper driver

If you want to use larger stepper motors than the Smoothieboard's drivers can handle ( 2A max ), you need to use external stepper drivers.

You can find detailed information on how to wire an external stepper motor driver to a Smoothieboard in the External driver appendix.

Stepper motor

They often have useful information on them

### Configuring

Example configurations are available in github https://github.com/Smoothieware/Smoothieware/tree/edge/ConfigSamples.

You can also refer to the Configuration documentation.

#### Current

The first thing you have to do is tell the stepper motor drivers what is the current rating for your stepper motors is. To drive the stepper motor correctly, the driver has to know the motor's current rating.

Each stepper motor model has a precise current rating. You can drive your stepper motor at a lower current, which will make it more silent, but also less powerful. But you can not drive the motor at a higher current than it is rated at. This would cause overheating, and possibly skipped steps.

The rating is often written on your stepper motor's label ( see picture on the right ). If it is not, you can get it by googling the stepper motor model number, or by contacting your seller or manufacturer.

Once you have the correct rating, you can set the corresponding parametr in the configuration file.

Smoothie has a funny way of naming stepper motor drivers. Instead of naming them X, Y or Z, because this makes no sense in non-cartesian robots like delta robots, we name the drivers using Greek letters so they are arm application agnostic :

Label on the Smoothieboard M1 M2 M3 M4 M5
Axis in a Cartesian machine X (left-right) Y (front-back) Z (up-down) E0 : First extruder E1 : Second extruder
Greek letter α (alpha) β (beta) γ (gamma) δ (delta) ε (epsilon)
Current setting configuration option alpha_current beta_current gamma_current delta_current epsilon_current

Now, as described in the "Unboxing" paragraph, connect the board to your computer, open the "config" file with a text editor, and change the configuration value for each stepper motor driver to the correct value.

For example, if your alpha stepper motor has a current rating of 1.68A, edit the corresponding line to read :

alpha_current                                1.68             # X stepper motor current


Do this for each stepper motor you have to connect to the board. (If you have a Cartesian robot, see which motor connects to which stepper driver in the array above. If you use another type of arm solution, see the specific documentation.)

A stepper motor

#### Steps per millimeter

A stepper motor driver operates in steps. It moves a certain number of steps in one direction, then a certain number of steps in another. You think in millimetres. You want your machine to go to a certain position in millimetres, then another position in millimetres.

You need Smoothieboard to convert the millimetres you ask of it, into steps the stepper motor driver understands.

That conversion depends on your exact arm solution. The most common, and the simplest, is the Cartesian arm solution, and it is the one we will focus on here. Documentation for other arm solutions can be found separately.

In the case of a Cartesian arm solution, you simply convert a certain number of millimeters to a certain numbers of steps. That is the steps_per_millimeter configuration option that you have to set for each stepper motor.

To compute it, you must multiply a certain number of factors.

• The object you move moves a certain number of millimetres for each rotation of the stepper motor. (This depends on the characteristics of the belt/pulley, or lead-screw system you are using.)
• The stepper motor moves a certain number of full steps per rotation. That is usually 200. (But it can be 400.)
• Each step is divided by the stepper motor driver in a certain number of microsteps. It is that number, and not the number of full steps, that we want. Smoothie always divides steps into 16 microsteps.

The formula is as follows :

$\text{(micro) steps per millimeter} = ( \text{full steps per rotation} * \text{microsteps per step} ) / \text{millimeters per rotation}$

To help you, there is an awesome calculator by the awesome Josef Prusa: http://calculator.josefprusa.cz/

Once you know the correct value for a given stepper motor driver, set it in the config file.:

alpha_steps_per_mm                           80               # Steps per mm for alpha stepper


Do this for each stepper motor driver.

In the case of your extruder stepper motor, the principle is the same, but the value is extruder_steps_per_mm.

Here are two good videos about steps-per-millimeters :

Pronterface

#### Direction

It is now time to test your stepper motors. For this you will need to use host software like Pronterface or the web interface.

Now connect to your Smoothieboard over the serial interface. Power your machine on by plugging the PSU into the wall.

Now you need to move an axis to make sure the stepper motor is turning in the right direction. In Pronterface, click near the yellow arrow marked "+X".

Your X axis will move. If it moved to the right, great! Everything is fine, and you have nothing to change. If it moved to the left, you need to invert the direction of that axis.

You do this by editing the configuration file, and inverting the direction pin for that stepper motor driver :

alpha_dir_pin                                0.5              # Pin for alpha stepper direction


Becomes :

alpha_dir_pin                                0.5!             # Pin for alpha stepper direction


This is for your axes. In the case of your extruder, the config value is extruder_dir_pin.

Save the config file, reset the Smoothieboard, connect again using Pronterface. Now the axis will move in the right direction.

Do this for each axis.

#### Moving bed

If you have a moving bed in the Y axis for example, as opposed to a moving tool, be careful : what matters is the direction of the head relative to the bed, not the direction of the bed relative to the machine. It's very common to get confused and invert your Y axis on moving bed machines (or not invert it when it should be). Basically, if an asymmetrical object looks like the model when it is printed, then your Y axis is correct, otherwise you need to change your configuration.

An endstop

It's essentially just a switch

## Endstops

End-stops are small interrupters that you put at the end of each of your axes. When you boot your machine up, Smoothie has no way of knowing the position of each axis. When it starts a print, Smoothie moves the axis until it touches that interrupter, and when it is hit, it declares that that is position 0 for that axis. And does so for all axes.

This allows Smoothie to then precisely know where everything is relative to that initial position. It is quite convenient as it saves you the hassle of actually moving the machine into that position when you want to start a print. Automation is great.

However, end-stops are not necessary, you could do without them. They are just so convenient that most machines use them.

End-stops can also be used as Limit Switches which prevent the machine from attempting to move beyond the physical limits of the axis (by pausing/stopping movement when triggered), see the Endstops page for details about configuring Smoothie to use End Stops as limit switches.

NOTE Smoothie does not allow you to use a zprobe as an endstop. An endstops must be dedicated to being an endstop and cannot be used as a zprobe and vice versa.

Endstop inputs on a Smoothieboard v1

There are 6 of them, two for each axis

### Mechanical endstop wiring

This will concentrate on the most common type of end-stops : the mechanical ones. Other types exist like optical or hall-o sensors.

#### Fancy Smancy

There are plenty of fun and futuristic endstop types around : optical, laser, magnetic, force-sensitive, infrared, inductive, etc…

However, please note that the general feedback from the community, is that most of those are either less precise, less repeatable, or much more difficult to get to "work right", compared to the classical "mechanical" endstop.

The mechanical endstop is actually likely the most precise, repeatable and easy to get to work option you have at your disposal. Just because these other options exist and have been explored by the community, does not mean they are better.

You might happen have a good reason to use a fancy endstop, but if you don't, it's likely a good idea to stick with a mechanical one.

Mechanical end-stops are simple interrupters : when not pressed, they do not let the current pass, when pressed, they let the current pass. By connecting a digital input pin on the Smoothieboard to the interrupter, and connecting the other side of the interrupter to Ground, the Smoothieboard can read whether or not it is connected to Ground, and therefore whether or not the end-stop is pressed.

Most mechanical end-stops have 3 connection points, to which you have to attach your wires :

• C : Common
• NO : Normally Open, meaning it is not connected to C when the interrupter is not pressed, and connected to C when the interrupter is pressed.
• NC : Normally Closed, meaning it is connected to C when the interrupter is not pressed, and connected not to C when the interrupter is pressed.

Wiring a basic NC endstop

You want to connect the Signal ( green in the schematic ) and Ground ( blue in the schematic ) pins for the end-stop on the Smoothieboard, to the C and NC connection points on the end-stop.

For each endstop, we connect C to Signal and NC to Ground because this means the digital input pin ( endstop connector ) will be connected to Ground in it's normal state and cut from Ground when the button is pressed. This approach is less prone to noise than the reverse. See here for more information.
Another positive effect of this approach is, that if a wire breaks for some reason you get the same signal as if the endstop is pressed. That makes sure that even with a damaged wire you are not able to overrun the endstop.

Order is not important as polarity is not important here.

Make absolutely sure that you do not connect VCC ( red ) and GND ( blue ) to a mechanical (microswitch) endstop! Depending on your wiring that may fries your smoothieboard instantly or when the switch gets pressed. There is a wiring where this not happens and you switch the signal between VCC and GND, but if you're not careful enough you damage your board.

You want to connect your X end-stop to the X min pins, Y end-stop to the Y min pins, and Z end-stop to the Z min pins.

### Powered endstops wiring

Mechanical endstops are simple switches, they simply let a signal pass through, or not, allowing us to detect their status with an endstop input. It has no intelligence of it's own.

There are more sophisticated endstops. Those are "powered endstops", for example : Hall-O ( magnetic ) or optical endstops.

The only difference between a mechanical endstop and those powered endstops is that they require being provided with 5V power.

This means that where for a mechanical endstop you connect the Signal and GND pins, for a powered endstop, you connect the Signal, GND and 5V pins.

Other than this, it works exactly the same as a mechanical endstop : The Signal pin receives something different depending on whether the endstop is triggered or not.

Different powered endstops have different behaviors :

Some connect Signal to Ground when triggered, and Signal to 5V when not triggered.

Others connect Signal to 5V when triggered, and Signal to Ground when not triggered.

To know exactly what your endstop does, see it's documentation.

If once wired, your endstop reports the opposite of what it should via the M119 command ( 1 when not triggered, and when triggered ), see the "Testing" section.

Some endstops might require removing their "pull-up" configuration, in this case, change :

alpha_min_endstop                            1.28^


To :

alpha_min_endstop                            1.28^


And if you need it to be a pull-down, change it to

alpha_min_endstop                            1.28v


In some very rare cases, the endstop reading circuit on the Smoothieboard will not be adequate for your endstop type. In this case, you should use a "free" GPIO pin on the Smoothieboard that nothing else uses to connect your endstop to.

See Pinout to find adequate pins.

### Testing

The default configuration most probably already has everything you need : the pins are already correct and the default speeds are reasonable.

Once they are wired, you can test your end-stops.

To do this, reset your Smoothieboard, then connect to it using host software like Pronterface or the web interface.

Now connect to your Smoothieboard over the serial interface. Power your machine on by plugging the PSU into the wall.

Now in Pronterface, home one axis by clicking the small "home" icon for that axis. Begin with X, then Y, then Z.

If your axis moves until it hits the end-stop, then stops when it hits it, moves a small distance back, then goes a bit slower back to the end-stop and stops, that end-stop is working fine.

On the other hand, if the axis moves a small distance in the wrong direction, then stops, you have a problem : your Smoothieboard always reads the end-stop as being pressed. So when you ask it to move until the end-stop is hit, it reads it immediately as pressed and stops there.

Another problem can be that the axis moves and never stops, even after the end-stop is physically hit. This means your Smoothieboard actually never reads the end-stop as being pressed.

There is a command that allows you to debug this kind of situation : in Pronterface, enter the "M119" G-code.

Smoothie will answer with the status of each endstop like this :

X min:1 Y min:0 Z min:0


This means : X endstop is pressed, Y and Z endstops are not pressed.

Use a combination of this command, and manually pressing end-stop, to determine what is going on.

If an end-stop is read as always pressed, or never pressed, even when you press or release it, then you probably have a wiring problem, check everything.

If an endstop is read as pressed when it is not, and not pressed when it is, then your end-stop is inverted.

You can fix that situation by inverting the digital input pin in your configuration file. For example if your X min endstop pin is inverted, change :

alpha_min_endstop                            1.28^


To :

alpha_min_endstop                            1.28^!


Here is the exact mapping of pin names to inputs on the Smoothieboard :

Endstop X MIN X MAX Y MIN Y MAX Z MIN Z MAX
Config value alpha_min alpha_max beta_min beta_max gamma_min gamma_max
Pin name 1.24 1.25 1.26 1.27 1.28 1.29

A spindle motor

They turn a tool at very high speeds

## Spindle Control

The Spindle is the main effector on your CNC Mill/Router. It holds the end mill or drill bit, makes it turn and remove material.

While manual control is sometimes fine ( turn it on before starting your G-code, off when you are done ), it is so much neater to have G-codes to control it automatically : simply put an ON G-code at the beginning of your G-code file, and a off G-code at the end of your G-code file, and you don't have to think about it any-more.

First thing you need to do is choose which component on the Smoothieboard is going to choose to control your Spindle.

### Controlling using a VFD

A VFD, or Variable Frequency Drive, is a box that takes mains power, transforms it into the voltage your spindle needs, and varies the frequency to control the speed of rotation of the spindle.

If you are using a VFD to power your spindle, you can use your Smoothieboard to control the VFD, start the spindle and control it's speed.

There are two methods, using Modbus, or using an analog signal.

For information on doing so, see the Spindle Module

This is the recommended method.

### Controlling using mosfets

If you are not using a VFD, an alternative is to use one of the mosfets on the Smoothieboard to control the spindle.

## Probing

Smoothie allows you to use a probe to do a variety of things :

• Calibrate machine geometry, for example for delta machines
• Automatically level un-even or non-level surfaces, using either grid or three-point methods
• Automatically find the distance between the tool and either the workpiece or the build surface
• Automatically detect tool lengths

## Panel

A panel is the combination of a screen, and some kind of input method, attached to the machine, that allows you to easily do things like move the carriage, start a file, monitor it's status, etc.

In order to use a panel with a Smoothieboard, you need to wire it to the board, and to modify the configuration file so the board knows it's talking to a panel.

There are different types of panels supported by Smoothieboard, to learn how to wire and configure for your specific panel, please read the Panel page.

## Appendixes

### Drilling canning cycles

Smoothie now supports drilling canning cycles, using the Drillingcycles module

However, if you do not want to use the module, there are solutions to convert those into "normal" G-codes :

### Printing, milling or cutting from the SD card

Printing, milling or cutting from the SD card on Smoothieboard is easy. First, you transfer your gcode files to the card. You can do this by moving the SD card to your computer and copying the files to it or simply copy the files to the card when it mounts on your desktop. If it isn't mounting automatically, you are probably running Linux and have automount disabled. You can change that or manually mount it. The other option is to use the built in Web Server if you have installed the RJ45 connector and an ethernet connection to the board. You can upload files to the SD card with this convenient Web interface.

Now, with your gcode files on the SD card, there are a few options to run it from there :

#### Serial terminal

You can use a serial port terminal application like CoolTerm (it supports OSX, Windows, Linux) or Cutecom ( OSX and Linux ). Once connected, enter help to get a list of supported console commands.

If you use Pronterface with your 3D printer, you can use its built-in serial terminal feature - just prefix serial commands with an "@". So, once connected to smoothie send "@help" and it will list all of the available commands.

You can also use the M24 G-code to play files from the SD card, see Supported G-codes.

#### Web interface

Another option is to use the Web interface mentioned above.

#### Panel

If you have a panel (like the RepRapDiscount GLCD) you can use the panel menus to run/pause/stop printing your gcode files.

### Wiring

How well your machine is wired is going to determine how long it lives and how resistant it is to breakage.

We have a great guide on different techniques and recommendations, please read the how to wire page.

### Crimping connectors

If your Smoothieboard came with connectors, you got connector casings, and crimps. You will need to attach your crimps to your cables, and then insert the crimps into the connector casings.

#### Patience

Please be careful and patient, if you have never done it before you will probably fail a few times before getting the hang of it. Also be careful to insert the crimp into your connector the right way around.

### Using two steppers motor on a single driver

Stepper motor drivers on Smoothieboard can handle up to 2Amps per driver.

If you want to control two separate motors with a single driver ( for example you have two stepper motors for your Y axis like on a Shapeoko, or two stepper motors for your Z axis like on a Reprap Prusa i3 ) and have both motors move simultaneously, you have two options.

If the total of the current used by your motors is more than 2Amps ( for example two 1.5Amps motors are 3Amps ), you can not wire them together on a single driver, and you need to look at doubling drivers just bellow.

However, if your total current is less than 2Amps, you can wire both motors in parallel to a single driver.

To do so, find for each stepper motor, which wires match which coils, and wire the same coils into the stepper motor connections on the Smoothieboard ( two wires per connection, one from each motor, for each pin ).

If when you test it, the two motors turn in reverse, you need to reverse one of the coils of one of the stepper motors, and they will start turning in the same direction.

You also need to set a current value for that driver that matches the total current your two motors will be using. For example if the motors are each 0.8Amps, your total is 1.6Amps and you need to set for that specific driver ( here gamma driver is shown ) :

gamma_current      1.6


### Doubling stepper motor drivers.

If you need to drive two motors with a single axis, but the total current used for the motors is more than 2Amps ( for example two 1.5Amps motors add up to 3Amps ), you can not wire the steppers in parallel to a single driver and have it control both motors at the same time like described above.

This is the case for example for the Y axis of Shapeoko machines.

In this case, you will need to use one driver for each of your motors. This means you need a Smoothieboard with one more stepper motor driver than you have axes. If you have 3 axes and need to double one, you will need a 4X or a 5X Smoothieboard.

To enslave a driver to another, you will need to connect the control pins for both drivers together.

For example if you want the epsilon ( M5 ) driver to be the slave to the gamma ( M3 ) driver you will need to connect :

• EN3 to EN5
• ST3 to ST5
• DIR3 to DIR5

The connectors for this can be found close to the stepper motor drivers, and are labelled.

Finally you need to do two things in your configuration file :

First, set the current value for both drivers. For example if you are using beta and delta set :

gamma_current       1.5
epsilon_current      1.5


Then, you need to make sure that none of the step, dir and enable configuration values for your slave stepper motor driver, are present in the configuration file.

For example if you are using gamma as a slave, make sure that none of the following values are present in the configuration file :

gamma_step_pin
gamma_dir_pin
gamma_en_pin


If they are, remove them. And be careful, for the delta driver, if you started from the 3D printer configuration file, they are not refered to as delta_xxx_pin but as extruder_xxx_pin, if they are present you must remove them all.

Only remove the lines for the slave driver.

### External Stepper Drivers

The logic pins that control the stepper drivers are broken out on all 5 axes to 1x4 pin headers found near each driver on the board. The 4 pins are EN, DIR, STP, and ground. These pins or their equivalents are found on most external stepper drivers. Many drivers call the STP (step) pin PUL (pulse). Some will call the DIR (direction) pin PHA (phase).

Most external drivers have both a + and - pin for each of EN, DIR, and STP. The simplest way to connect the external driver is to wire Smoothieboard GND to all 3 - pins, and the logic pins of Smoothieboard to the corresponding + pins. Note that Smoothie is 3.3V logic and each pin can only supply a maximum current of 4 mA, which is not usually a problem unless interfacing to very large, or very old external drivers which may need a little more.

#### Pins

While this example will show using the pins of one of the on-board drivers to control the external driver, you can use pretty much any free GPIO pin to control the step/direction/enable pins on your external driver.

See pinout and pin usage to find free pins.

All loadouts of Smoothieboard (3x, 4x, 5x) can control 5 external stepper drivers using these ports. The presence or absence of a built in driver will not affect the external driver.

Wiring an external driver with a common cathode

This shows control of an external driver using the pins on the positive side of the external driver's input.
GPIO pins are taken to the positive inputs on the driver, and the ground is shared.

Please note, if your external driver requires 5V, that Smoothieboard only provides 3.3v on it's output pins.

Two solutions to this : either use a level shifter or use the Smoothieboard's pins as Open-Drain ( ie linking to ground instead of linking to 3.3v, when closed ), and wire accordingly.

For example :

Wiring an external driver with a common anode

Here, the 5V is taken from an endstop input's positive terminal, taken to the 5V inputs on the external driver. The step/direction/enable pins on the Smoothieboard are taken to the GND inputs on the external driver.

In this case, you will also need to change those pins to be open-drain. To change a pin from being normal to being open-drain, you add a o to the pin's number. For example :

alpha_step_pin    2.0      # Pin for alpha stepper step signal


becomes

alpha_step_pin   2.0o     # Pin for alpha stepper step signal


#### ReprapDiscount Silencio

It does 1/128 microstepping, so using it with Smoothie makes a lot of sense since Smoothie can do higher step rates.

It comes with an adapter for pololu-type drivers for RAMPS-type boards. However, you can also simply wire it to Smoothie's external driver connectors.

The only catch is : the pins are not in the same order in Smoothie and on the driver's cable. (Note the colors maybe different on your cable)

 Silencio cable color Black Green Red Blue Silencio connector order +5v Enable Direction Step Smoothie connector order Ground Step Direction Enable

No big deal though, you simply need to swap the step and enable pins in the configuration file.
Also DO NOT connect the Black wire to the 4th pin om smoothie which is gnd on smoothie, it must be connected to a +5v pin elsewhere (eg on the endstops)

Additionally, you need to invert ( by adding a ! to the pin number ) the enable pin ( that's specific to the Silencio )
The step pin does not need to be inverted.

For example for your alpha driver, change :

alpha_step_pin      2.0       # Pin for alpha stepper step signal
alpha_dir_pin       0.5       # Pin for alpha stepper direction
alpha_en_pin        0.4       # Pin for alpha enable pin


to

alpha_step_pin        0.4       # Pin for alpha stepper step signal
alpha_dir_pin         0.5       # Pin for alpha stepper direction
alpha_en_pin          2.0!      # Pin for alpha enable pin


And just wire the Silencio connector to the Smoothieboard external driver connector

### Solid State Relays

The big mosfets on the Smoothieboard can handle up to 12Amps. Sometimes that's not enough. Say you want to control a big spindle, a gigantic heated bed, or a tesla coil.

Typical Solid State Relays ( SSR ) can handle up to 40Amps easily, sometimes more. AC ones can run 220V AC, and DC ones up to 60V DC ( typically, look at the specs for yours ).

To control your Solid State Relay ( SSR ), you will need one GPIO pin ( use one of the free ones on the board ideally ), and a connection to GND ( plenty of those ).

A SSR is essentially a big switch : you cut a wire, plug each end of the cut wire into it's two terminals, and then you'll be able to control whether or not those two ends of the wire connect or not. Simple as that.

Wiring a Solid State Relay

You will need to connect GND on the Smoothieboard to the "-" connection on the Input side of the SSR, and the GPIO pin on the Smoothieboard to the "+" connection on the Input side of the SSR. This example shows using P1.30

Then simply configure the module that will be using the SSR to use that pin, for example in the case of Switch :

switch.misc.enable                   true #
switch.misc.input_on_command         M42  #
switch.misc.input_off_command        M43  #
switch.misc.output_pin               2.4  # GPIO pin we connected to "+" on the SSR
switch.misc.output_type              digital        # just an on or off pin


In the case of TemperatureControl, where you use the SSR to control a heating element for example, there is a catch.

SSRs have a low maximum frequency they can be switched at. You need to specify that frequency or Smoothie will drive it way too fast. In this example, the maximum frequency is 20Hz.

So, you need to modify your module to both use the correct pin ( the free GPIO you wired to the SSR ), and to the correct frequency. Here are the two lines to change :

temperature_control.swimming_pool_heating.heater_pin               2.4
temperature_control.swimming_pool_heating.pwm_frequency            20


Another option, which turns the heaters on/off even less often, is to use bang-bang, where the state is only changed when temperature deviates too much from the set value :

temperature_control.bed.bang_bang            true            # set to true to use bang bang control rather than PID
temperature_control.bed.hysteresis           2.0             # set to the temperature in degrees C to use as hysteresis
# when using bang bang


### Swapping stepper motor drivers

On some boards, you might want to swap two axes.

For example, you have a board that has two connectors on the Z axis, but you want to connect two motors to the Y axis ( which has only one connector ).

In that case, all you need to do is exchange the 3 pin definitions for these two axes.

For example :

beta_step_pin                                2.1              # Pin for beta stepper step signal
beta_dir_pin                                 0.11             # Pin for beta stepper direction
beta_en_pin                                  0.10             # Pin for beta enable

gamma_step_pin                               2.2              # Pin for gamma stepper step signal
gamma_dir_pin                                0.20             # Pin for gamma stepper direction
gamma_en_pin                                 0.19             # Pin for gamma enable


Becomes :

beta_step_pin                                2.2              # Pin for beta stepper step signal
beta_dir_pin                                 0.20             # Pin for beta stepper direction
beta_en_pin                                  0.19             # Pin for beta enable

gamma_step_pin                               2.1              # Pin for gamma stepper step signal
gamma_dir_pin                                0.11             # Pin for gamma stepper direction
gamma_en_pin                                 0.10             # Pin for gamma enable


Please note that the current control parameters do not get swapped : alpha_current always controls the current for M1, no matter what you do to the step/direction pins.

### Which pins are which

#### Smoothieboard pinout

Full size version

#### Smoothieboard pin capabilities

Full size version

Also see the pin usage table

Notes :

• Do not use endstop inputs as outputs ( for example to control a solid state relay ), this will not work.

### Protecting a power input with a fuse

A Fuse is a device which sacrifices itself ( gets destroyed and stops letting electricity through ) if the current passing through it is higher than a certain value.

You need to choose a fuse with a value higher than your "mormal" current for a given circuit. For example if your heated bed consumes 10A, you want to have a 15A fuse protecting it, that way if everything is fine the fuse does not burn, but in case of a short circuit, it does.

Here is an example of a fuse protecting the mosfet power input :

Protecting your board with a fuse

Note the fuse must have an adequate rating

## Troubleshooting

If you run into trouble, something doesn't work as it should, head over to the Troubleshooting page for a list of common problems and means of diagnosis.

You can also contact the Community for help if you can't find an answer in the documentation.

## bCNC configuration

bCNC is program which makes it convient to use Smoothie as a CNC mill or laser cutter, and better yet, it is free! It also comes with several features useful for CNC and laser work, such as a work coordinate system, basic CAM, and a remote pendant web app.

#### Be Careful

Failure to properly configure bCNC for use with smoothie can result in a your machine crashing, parts breaking, and being sad. Be careful and check your work.

The first step is to update your SmoothieBoard to the latest, stable, version of the firmware, as support for bCNC is relatively new. Remember, before you upgrade to a new firmware, backup your config, config override and old firmware. See flashing firmware for more help. Once you have update your firmware, go to your configuration file and add grbl_mode true somewhere, as this is what tells the board to talk to bCNC in the correct way.

The second step is to get bCNC, which is available at https://github.com/vlachoudis/bCNC. Simply download and extract the archive or bCNC and run bCNC.bat after installing all of the dependencies as listed on the ReadMe. Once installed, select Smoothieboard from the drop down menu on the communication panel under the File tab and edit the machine configuration under the Tools tab.

Once all of these things are done, you are ready to use bCBC with Smoothie!

## Software

All software bellow either knows how to interface with, or how to generate g-code for, Smoothieware.

#### CNC

• bCNC - Open-Source CNC host with great preview and other operations. Set machine type to smoothie. and add grbl_mode true to your smoothie config (Note: You must update to the latest version of Smoothieware to ensure compatibility with bCNC).
• OpenSCAM.org - Open-Source Simulation & Computer Aided Machining (Free 3-axis CNC Simulator which understands G-Code)
• GCode plug-in for InkScape - CAM, Output GCode from SVG files in Inkscape.
• PyCAM - Open-Source CAM software.
• jscut - Open-Source in-browser CAM software.
• CamBam - Closed-Source, but cheap and feature-full CAM software. Widely used by hobbyists.
• Fusion360 - Closed-source CAM with very advanced features, free for hobby/fablab/small business.
• Universal Gcode Sender Host program
• Fabrica - Easy to use web control interface ( Host )

#### Lexicon

A few words you will see in this documentation that require a bit of explanation :

• «Host» software is software that is used to "talk" to your Smoothieboard. It allows you to control the machine ( for example "jog" the axes ), to "stream" a G-code job, or to upload it to the SD card, things like that.
• «Slicing» software is software that is used to take a 3D model file, and based on some settings you input, "slice" it into layers, and generate a G-code file that the Smoothieboard can then execute to print a thing.
• «CAM» software, or «CAM Package»», for Computer Assisted Manufacturing, is software that is used to take a 3D or 3D file, and based on some settings you input, transform it into a list of tool movements ( G-code file ) for a machine that uses a tool to remove material from a workpiece.

This site is a WIki, which means you are very welcome to help us improve it. Help on how to do that can be found at the Editing the Wiki page . You can edit any page by clicking the "Edit" button bellow :
page revision: 34, last edited: 23 Jan 2017 22:15